VoCore2 Ultimate - Linux SBC with WiFi and Dock

VoCore2 is a tiny single-board computer. Use it for all types of projects where tiny size, inexpensive cost and built-in WiFi are important. The VoCore2 is open hardware which runs Linux and has WiFi, USB, UART, 20+ GPIOs and more. One inch square! VoCore2 Ultimate also contains a microSD slot, USB2.0 port, A/D, D/A, 10/100 Ethernet port, audio record/playback, up to 300Mbps wireless transfer speed and low power consumption. The VoCore2 can be used as a super tiny WiFi router! VoCore2 is a new revision of the original VoCore v1.0, making it faster and more stable without increasing the size! Links to compliance information available at the bottom of this listing. KEY FEATURES Approximately 1 inch cube Built-in WiFi, 802.11n, 2T2R, speed up to 300Mbps Built-in Antenna, U.FL slot CPU: MT7628AN, 580MHz, MIPS 24K Memory: 128MB DDR2 @ 166MHz Storage: 16MB NOR on board, supports up to 2TB SDXC cards Ethernet: 1 port / 5 ports, up to 100Mbps USB 2.0 port PCIe 1.1 supported UART x3 (UART2 for debug console) GPIO Pins: >= 40 (pinmux) PWM x4 Runs Linux - Preloaded! A/D Conversion - 4 channels D/A Conversion - 1 channel Audio playback and recording supported Dimensions: 28 x 30 x 30 mmPower input: 3.6V ~ 6.0V Power consumption: 74mA WiFi standby, 230mA WiFi full speed, 5V input NOTES Please update to the latest VoCore2 Ultimate firmware for best performance. QUICK START Attach microUSB port to a stable power source, such as a USB charger or computer USB port. DO NOT SUPPLY MORE THAN 6.0V as that will damage your VoCore2. The SSID "VoCore2" should be accessible from other devices within 30 seconds of applying power. Connect to the SSID "VoCore2" from your wireless device (phone, computer, laptop, tablet, ODROID, etc.) Use one of the following two methods to connect:     1. Open an SSH terminal ("ssh" on Linux/Android, "PuTTY" on Windows, etc.) and log in to "VoCore2" (user: root, pass: vocore)     2. Using USB2TTL, you can connect to the VoCore2 through another computer's USB port (no driver required). Once connected, a serial port should show up for the VoCore2. NOTE: UART speed is 115200bps, 8bit, no parity, 1 stop bit. For Windows, USB2TTL device should appear in Device Manager. For Linux/MacOS, USB2TTL device should appear at /dev/tty.usbmodem_1 The VoCore2 is now in AP (Access Point) mode. It is possible to put the VoCore2 in AP + STA mode, which allows the VoCore2 to connect to a wireless hotspot (AP) and provide wireless access from that hotspot to anything connected to the AP and Ethernet port. APPLICATIONS NIC AP/Router Embedded Applications NOTE PCB may be green or white in color LINKS ameriDroid Learn - https://ameridroid.com/blogs/ameriblogs/tagged/vocore Tutorials and other useful information - http://vocore.io/v2u.html Hardware Sources - http://vonger.cn/misc/vocore2/source.zip Firmware (2018-07-23) http://vonger.cn/misc/vocore2/20180723V.bin Flash Image [md5:f4c527a1e563d0ad7ef9ab0b5e0b35c6] - http://vonger.cn/misc/vocore2/ultimate.16m.img Toolchain for Ubuntu 14.04 x64 - http://vonger.cn/misc/vocore2/toolchain.tar.bz2 Datasheet - http://vonger.cn/misc/vocore2/datasheet.zip VoCore Forum - http://forum.vocore.io VoCore Wiki - http://vocore.io/wiki.html VoCore Blog - http://vonger.cn/ CERTIFICATIONS Information in the MT7628.pdf file - http://vonger.cn/misc/vocore2/datasheet.zip Discussion at VoCore Forum - http://forum.vocore.io/viewtopic.php?f=16&t=3959&p=6540 Warranty is valid for thirty days, starting upon date of receipt.