Studio Technologies Model 370A 2-Channel Intercom Beltpack

Studio Technologies Model 370A 2-Channel Intercom Beltpack The Studio Technologies Model 370A Intercom Beltpack begins with the features offered by traditional 2-channel party-line intercom user devices and adds a range of new capabilities, along with the advanced performance and flexibility that Dante audio-over-Ethernet provides. Over a standard IP network, multiple Model 370A units can be used in party-line (PL) intercom applications with help from an external Dante-enabled audio matrix such as the Studio Technologies Model 5422 Dante Intercom Audio Engine. Alternately, units can be used “point-to-point” or interfaced with Dante-compatible matrix intercom systems. Key Features Dante audio-over-Ethernet technology Two independent talk and listen channels Integrated call function Supports dynamic and electret microphones 5-pin female XLR headset connector Excellent audio quality Uses STcontroller for configuration AES67 and Dante Domain Manager support Power-over-Ethernet (PoE) powered Technical Specifications Power Source Power-over-Ethernet (PoE): class 1 (very low power, =3.84 watts) per IEEE 802.3af Network Audio Technology Type Dante audio-over-Ethernet AES67-2013 Support yes Dante Domain Manager (DDM) Support yes Bit Depth up to 24 Sample Rate 48 kHz Number of Transmitter (Output) Channels 2 Number of Receiver (Input) Channels 2 Dante Audio Flows 4; 2 transmitter, 2 receiver Network Interface Type 100BASE-TX, twisted-pair Ethernet, Power-over-Ethernet (PoE) supported Data Rate 100 Mb/s (10 Mb/s and 1000 Mb/s “GigE” Ethernet not supported) Audio Channels 2 talk, 2 listen Microphone Input Compatibility dynamic or electret (low-voltage DC-powered) microphones Type unbalanced Electret Microphone Power 5 volts DC via 2.21 k resistor, selectable on/off Gain 22, 30, 42, or 48 dB, selectable, ref. -60 dBu input to Dante output (-20 dBFS nominal) Frequency Response 50 Hz to 10 kHz, -3 dB Distortion (THD+N) <0.02% Dynamic Range 75 dB Compressor Threshold 1 dB above nominal level (-19 dBFS) Slope 2:1 Status LED compressor active Headphone Output Type 2-channel Compatibility intended for connection to stereo (dual-channel) or monaural (single-channel) headsets with nominal impedance of 50 ohms or greater Maximum Output Voltage 3.8 Vrms, 1 kHz, 150-ohm load Frequency Response 20 Hz to 10 kHz, -3 dB Distortion (THD+N) <0.002% Dynamic Range >100 dB Call Function Signaling Method 20 kHz, ±800 Hz, within audio channels Call Send Level -20 dBFS Call Receive Level -27 dBFS minimum Connectors Headset 5-pin female XLR Ethernet Neutrik NE8FBH etherCON RJ45 receptacle USB type A receptacle (located inside Model 370A's enclosure and used only for application firmware updates) Configuration Requires Studio Technologies STcontroller software application, version 1.06.00 and later (STcontroller is compatible with Windows version 7 and later) General Operating Temperature 32° to 122°F (0° to 50°C) Storage Temperature -40° to 158°F (-40° to 70°C) Humidity 0 to 95%, non-condensing Altitude not characterized Dimensions (WxHxD) 3.6 x 1.6 x 4.8” (9.2 x 4.0 x 12.6cm) Mounting intended for portable applications; contains integral belt clip; optional MBK-01 Mounting Bracket Kit allows Model 370A to be permanently mounted Weight 0.6Lbs (0.3kg)