Ebyte Buy E18-MS1-PCB TI Preis CC2530 chip 2.4GHz igBee RF Module Smart home Antomation

E18-MS1-PCB Ebyte ZigBee RF Module CC2530 Smart home Antomation Network OEM E18-MS1-PCB IOT Solution [IC]：CC2530 [Frequency]：2.4~2.48GHz [Power]：4dBm [Distance]：0.2km [Interface]：UART/IO [Weight]：1.2±0.1g [Introduction]：E18-MS1-PCB is based on original imported RF chip CC2530 form TI in American. The IC chip is integrated with 8051 microcontroller and wireless transceiver inside, which is applicable to Zigbee design and 2.4GHz IEEE 802.15.4 protocol. All the IO ports are led out by the module, which means that multi-aspect development is realizable. Detailed parameters RF Parameter Value Remark Working frequency 2400~2480 MHz Default:  2.4GHz (32MHz oscillator) Transmitting power 4 dBm About 2.5mW Receiving sensitivity -96.4 dBm Air data rate: 250kbps Communication protocal ZigBee - Test distance 200m In open and clear air, with maximum power, 5dBi antenna gain, height of 2m, air data rate: 250kbps Hardware Parameter Value Remark IC CC2530F256RHAT/QFN40 - FLASH 256 KB - RAM 8 KB - Core Industry-standard enhanced 8051 MCU - Size 14.1 * 23.0 mm - Antenna type PCB - Communication interface SoC - Package SMD -   Electronic parameter Min. Typ. Max. Unit Condition Power supply 2.0 3.3 3.6 V Communication level 2.0 3.3 3.6 V Transmitting current 26 28 31 mA 4dBm（2.5mW） Receiving current 25 27 30 mA Sleep current 0.6 1.2 1.8 μA Operating temperature -40 20 +85 ℃ Operating humidity 10 60 90 % Storage temperature -40 20 +125 ℃   Pin parameters Pin number CC2530 Pin name Module Pin name Input/Output Pin usage 1 GND GND Ground wire, connected to the power reference ground 2 VCC VCC Power supply, must be between 1.8' 3. 6V 3 P2.2 GPIO I/O DC-download program or Debug clock interface 4 P2. 1 GPIO I/O DD-download program or Debug data interface 5 P2.0 GPIO I/O N/C 6 Pl. 7 NWK_KEY I Used for manual join, exit, and quick match keys. Not networked: Short press to join the network or create a network operation; Networked: Short press for quick match; Long press means to leave the current network; Note: Low level is valid, 100ms W short press W 3000ms, 5000 W long press. 7 PL 6 GPIO I/O N/C 8 NC NC N/C 9 NC NC N/C 10 Pl. 5 UARTO.TX I Serial port TX pin 11 Pl. 4 UART0_RX 0 Serial port RX pin 12 Pl. 3 RUN_LED 0 It is used to indicate the network access status of the module. Fast flashing 256 times (10Hz frequency) indicates that it is joining the network or creating a network, and slow flashing 12 times (2Hz frequency) indicates that the module has joined the network or successfully created the network; Low level lights up; 13 Pl. 2 NWK_LED 0 It is used to indicate the one key pairing status of the module, provided that two modules need to join the same coordinator, and then one key pairing can be performed. In the transparent mode, mutual transparent transmission can be performed. Low level lighting; 14 Pl. 1 GPIO I/O The PA transmit control pin has been connected inside the module; There is no PA inside the E18-MS1-PCB/E18-MS1-IPX; 15 P1.0 GPIO I/O The PA receiving control pin has been connected inside the module; There is no PA inside the E18-MS1-PCB/E18-MS1-IPX; 16 P0.7 HGM 0 HGM pin of PA; E18-MS1-PCB/E18-MS1-IPX has no PA inside, so this pin is used as GPIO port; 17 P0.6 GPIO I/O N/C 18 PO. 5 GPIO I/O N/C 19 P0.4 GPIO I/O N/C 20 P0.3 GPIO I/O N/C 21 P0.2 GPIO I/O N/C 22 PO. 1 GPIO I/O N/C 23 PO.O GPIO I/O N/C 24 RESET RESET I Reset port