MANTA 13X Lite 13 inch FPV Drone DJI O3 / Axisflying 5.8G 3W VTX Long Distance FPV Drone Kit
The MANTA 13X Lite FPV Drone Kit is built for long-range and endurance-focused pilots. Featuring a lightweight 13-inch carbon frame, it supports DJI O3 HD systems and includes the Axisflying 5.8GHz 3W VTX for unmatched signal range and penetration. Ideal for cinematic exploration, freestyle power loops, and DIY builds. Product parameters:Product name: Manta 13 X LiteStructure: True XWheelbase: 600mmLower plate thickness: 3mmUpper plate thickness: 3mmCarbon plate material: T700Arm size: 20mm*20mm*294.3Camera width: 20mmFlytower installation hole: M3*30.5mmImage transmission hole distance: M2*20/25.5mm M3*30.5mmPropeller installation size: 13inch Motor hole: M4x30mmBody weight: about 2.8KG Configuration:Motor: 4214-380KVRecommended battery: Lipo 8000mAh 8sPropeller: 13inchFlytower: Argus 80A +F722Image transmission: DJI 03 or Axisflying 5.8GPayload: 3.5 ~ 6kgFlying Time: With Load Flying Time 8-15minNo Load: 25minFlying Distance: 10kmMax Speed: 120km/hMax Altitude: 5000m Frame: 13-inch CarbonStructure: True XWheelbase: 600mmBottom Plate Thickness: 3mmTop Plate Thickness: 3mmCarbon Plate Material: T300/T700Height of Electronic Device Layer: 20mmArm Size: 20mm*20mm*294.3Camera Spacing: 20mmStack Mounting Hole: M3*30.5mmVTX Mounting Hole: M2*20/25.5mm M3*30.5mmPropeller Installation Size: Max 13 inchMotor Mounting Hole: M4 x 30mm Motor: 4214 380 KVKV Value: 380KVOperating Rated Voltage: 6-8SNo-load Current: 2.8A/20VPhase Resistance: 48mΩMotor Weight: 246gMaximum Current: 60AMaximum Power: 1760 WMaximum Thrust: 4850gMotor Size: Ф49x32.5mm Flight Control: F722MCU: STM32F722RET6Gyroscope: ICM42688Barometer: DPS310 or SPL06Blackbox: 16 MOn-Screen Display: AT7456BEC: 5V2A ,9V2AInput Voltage: 12-50V(3-6S Lipo Recommended)Firmware: BetaflightNumber of Serial Ports: 6 GroupsSupported Motors: M1 M8Weight: 40.6x40.6x9.8mmSize: 19.6gMounting Hole Spacing: 30.5mm/M3 ESC: 80A 8SFirmware Name: QH 40_24_V0.19.2Current Ratio Value: 200Input Voltage: 8SContinuous Current: 80ABurst Current: 90AESC Telemetry: Not supportedBEC: Not supportedSize: 57*56*6mmMounting Hole Spacing: 30.5*30.5mmWeight: 28g Camera: B19 Product Manual Cam 1500TVLModel: HD 1500TVL (upgraded version, with OSD tuning board)Image Sensor: 1 / 3′CMOSPixels: 1500TVLLens: 2.1mmSignal System: PAL / NTSC (adjustable via OSD)Signal-to-Noise Ratio: ＞ 60Db（AGC OFF）Electronic Shutter Speed: PAL: 1 / 50-100.000, NTSC: 1 / 60-100,000Electronic Shutter: PAL: /50 - 100,000; NTSC: 1/60 - 100,000Automatic Gain Control (AGC): Low / Medium / HighBacklight Compensation (BLC): YesMinimum Illumination: 0.001Lux / 1.2FWDR: D-WDRDNR: 3DNRDay/Night: Auto/Color/B&WPower Supply: DC 5V-30V Image transmission VTX: 5.8G 40CH 3WModel: DJI O3 / Axisflying 5.8G (Optional)Supported Voltage: 7-28VBEC: 5V / 500mATransmission Power: 25mW / 13.95dBm; 2500mW / 34.04dBmAntenna Interface: MMCXOutput Power: PIT / 25 / 2500mWStandard 40 Channels: A / B / E / F / RVideo Transmission Protocol: SmartAudioMounting Holes: 20X20.M2Size: 25mmX37mmx6.5mmWeight: 19g Antenna: 5.8G RHCP 150MM*The whole is made of imported PC+ABS material which can withstand high strength impact *Impact resistant double-sheathed semi-rigid cable *Root reinforcement design, 360 ° protection RX: ELRS 915MHzProcessing Chip: ESP8285RF Chip: SX1276IMLTRTPower Input: 5VOperating Current: 100mAOperating Protocol: CSRFReceiving Frequency Range: 915MHz or 868MHzSize: 12mm12mm3mmWeight: 0.6g (without antenna)Antenna Connector: IPEX1Telemetry Output Power: <17dBmFirmware Update Method: WIFI Propellers: Gemfan Prop 1308Type: 1308Blades: 3Material: Fiberglass NylonPitch: 8 inchCenter Hole lnner diameter: 6mmWeight/g: 39g Package weight: 2.8kgPackage size: 35.5*35.5*16cm Note: Batteries and transmitters are not included in the package **We are the source manufacturer, welcome to purchase in bulk!