Lee 6 Cav Combo w/ Handles & Sizing Kit for 32-20 WCF/32 S&W Long/32 Colt 90308

img{max-width:100%} Lee 6 Cavity Mold with Handles and Sizing and Lube Kit Combo 90308+90005+90039+90177 NEW!!  90308   311-93-1R 32-20 WCF / 32 S&W Long / 32 Colt(311 Diameter)       93 Grain       1 Ogive Radius Designed for volume production, the Lee 6-Cavity Bullet mold blocks are machined from commercial quality aluminum andfeature steel bushing and alignment pins. Lee mold blocks are machined from aluminum blocks making making them rust resistant.  Aluminum molds heat up and cool down faster than iron or  steel molds so good bullets can usually be produced after only a few casts.In addition, they are one-third the weight of iron or steel mold blocks for less fatigue during extended casting sessions.  To ensure the best possible bullets, mold block halves are CNCmachined for unmatched roundness and size control. Lee 6-Cavity molds come with a cam operated, hard-anodized sprue plate which is held tightly with tempered spring washers at each end. Weights given are Lee's weights with suggested alloy; actualweight may vary due to alloy mixture used. Notes: Material: Machined Aluminum Mold Blocks and Hard Anodized Sprue Plate. Cavities: 6Features:Rust resistant aluminum blocks.Lathe bored blocks with steel bushings & aluminum pins. + 90005 Commercial Mold Handles for 6-Cavity Lee Mold New   Lee Commercial Bullet Mold Handles for 6-Cavity Bullet   Molds are necessary for using Lee 6-Cavity molds which do  not ship with handles. These handles also fit the Lee 18 Cavity Buckshot molds. This handle has a steel frame and hardwood grips which are designed to last a lifetime. Material: Hardened Steel frame, Hardwood gripped Fits: Lee 6-Cavity and 12-Cavity Bullet Molds  + Bullet Lube and Size Kit.311 DiameterNew90039+90177 The Lee Lube and Size Kit is one of the fastest and easiest ways to lubricate and size cast bullets. The sizing die that comes with the kit fits in any press that acceptsstandard 7/8"-14 threaded dies.Bullets are pushed through the sizing die nose first, so no special toppunches are needed.Gas checks are automatically seated and crimped in place. Sized bullets are captured in the special container and a 4 oz bottle ofLee Liquid Alox bullet lube is included. Material: Hardened Steel Sizing Die, Plastic HopperFunction: Size cast bulletsNotes:Comes in red plastic case.Lee recommends bullets be re-lubed after sizing to be sure the sizedportion is coated with Alox.All lead bullets must be lubricated, but it is not absolutely necessaryto size all cast bullets.Bullet must be sized if they are so large that they expand the case toomuch to freely enter the gun's chamber.Sizing sometimes helps accuracy by making the bullet uniform indiameter.Sizing helps insure uniform start pressure and better accuracy.Gas checks can be installed with this tool.Simply place the gas check on the base of the bullet before sizing. Directions for Use: Lubricating Bullets:1. Place bullets in provided red plastic container and drop in the included.Lee Liquid Alox onto the bullets.2. Gently shake the bullets in an orbital motion to coat the bullets.If they do not coat completely, add a little more lube. 3. Spread the bullets onto waxed paper and let dry overnight.4. Load at least one bullet into a case and check to be sure it easily chambersin the gun.If it fits tightly, you must resize the bullet before loading.Directions for Use: Sizing Bullets:1. Screw the sizing die into any standard reloading press.Exact depth is not important.2. Install the bullet punch into the ram.This fits all rams that use standard shellholders.3. Place the red plastic container with the lubed bullets inside on top of the sizing die.4. Place bullet on the punch and push the bullet through the die.5. When 3/4 of the bullets have been loaded, lift the red plasticcontainer off the die. Invert the holder before opening.6. For rifle and hot pistol loads, it is best to re-lube the bullets toensure the sized portion is re-coated. ~~~~~~~~~~~~~~~~~~~~ We are a Factory Direct Dealer of Lee® Precision, Inc.  ALL MANUFACTURERS WARRANTIES WILL APPLY ! All of our products are BRAND NEW in the box; and contain all of the parts,  materials and documentation. You can expect and will receive prompt delivery of your item. We will ship your order within ONE DAY! We are unable to accept returns on used, fitted, or altered parts.  Returns must be in new, unused condition and in their original packaging.