17 Bit Absolute Servo Motor 400w 600w 750w 1kw With 60 80 Flange AC 220V Servo Driver High Accuracy Magnetic Servo 3000-6000RPM

  Servo Motor With Magnetic 17bit Absolute Encoder Servo Motor Model Motor Flange Power Motor Shaft Diameter 60AST-A1C01330 Nema24 60mmx60mm 400w 14mm With 5mm Key 60AST-A1C01930 600w 80AST-A1C02430 Nema32 80mmx80mm 750w 19mm With 6mm Key 80AST-A1C04025 1000w 400W 1 x 400W  60AST-A1C01330 Servo Motor （17 bit absolute）1 x T3D-L15A AC driver (English manual  via email） 1 x 3M encoder cable1 x 3M motor cable1 x Control signal cable2 x 2K 1/4W resistance 1 x RS485 cable600W1 x 600W  60AST-A1C01930 Servo Motor（17 bit absolute）1 x T3D-L15A AC driver (English manual  via email） 1 x 3M encoder cable1 x 3M motor cable1 x Control signal cable2 x 2K 1/4W resistance 1 x RS485 cable750W1 x 750W  80AST-A1C02430 Servo Motor（17 bit absolute）1 x T3D-L20A AC driver (English manual  via email）1 x 3M encoder cable1 x 3M motor cable1 x Control signal cable2 x 2K 1/4W resistance 1 x RS485 cable 1kw1 x 1kW  80AST-A1C04025 Servo Motor（17 bit absolute）1 x T3D-L20A AC driver (English manual  via email）1 x 3M encoder cable1 x 3M motor cable1 x Control signal cable2 x 2K 1/4W resistance 1 x RS485 cable Startup setting parameters: Find P-098 and change it to 1 Find the E-SEF, and long press the confirmation key to display DONE saved successfully. Power off and restart after all parameters are set.   Technical Specifications 60AST-A1C01330 60AST-A1C01930 80AST-A1C02430 Rated voltage (V) 220 220 220 Rated power (W) 400 600 750 Rotor pole pairs (P) 5 5 5 Rated torque (N.m) 1.27 1.91 2.4 Instantaneous maximum torque (N.m) 3.82 5.73 7.2 Rated speed/Maximum speed (rpm) 3000/6000 3000/6000 3000/5000 Rated current (A(rms)) 2.8±10% 4±10% 4.8±10% Instantaneous maximum current (A(rms) 8.4±10% 12±10% 14.4±10% Moment coefficient (N.m/A(rms)) 0.42±10% 0.54±10% 0.5±10% Back EMF coefficient (X10 V/rpm) 27.5±10% 32.5±10% 33.2±10% Resistance (Ω) 3±10% (20℃） 3.2±10% (20℃） 1.6±10% (20℃） Inductance (mH) 7.8±20% (20℃） 8.4±20% (20℃） 9.5±20% (20℃） Moment of inertia (X10 V/rpm) 0.68[0.73]±10% 0.82[0.87]±10% 1.72[1.77]±10% Maximum radial load (N) 245 245 392 Maximum axial load (N ) 74 74 147 Weight (KG) 1.22[1.65]±10% 1.4[1.7]±10% 2.2[3]±10% protection structure IP65 Insulation class F Insulation resistance DC500V 20MΩ以上 Insulation withstand voltage AC1500V1分钟 turn around Forward turn command, viewed from load side: Counterclockwise (CCW) Vibration level Rated A for operation surroundings Temperature -20℃~40℃, humidity 20%-80%RH(no condensation), altitude below 1000 (above the temperature, altitude range to reduce the rating) Temperature -20℃~60℃, (no freezing) humidity 20%-80%RH(no condensation) impact strength 98m/S² Vibration resistance 49m/S² 400 600W 750W Rated voltage DC (V) 24±10% 24±10% 24±10% Rated power (W) 7.2 7.2 13 Excitation current (A) 0.3 0.3 0.56 Insulation class F F F Static torque (N.m) ≥1.5 ≥2 ≥4 Insulation resistance (Mω) ＞500 ＞500 ＞500 Resistant to high voltage 1500V/1S/5mA 1500V/1S/5mA 1500V/1S/5mA Rotary clearance ≤0.5 ≤0.5 ＜0.5 Operating ambient temperature -10~+40 -10~+40 -10~+40 Attract time ≤50 ≤50 ≤60 Release time ≤20 ≤20 ≤20 Attract voltage ≤19.2 ≤19.2 ≤19.2 The release of the voltage ＞1.5 ＞1.5 ＞1.5 Running noise ＜60 ＜60 ＜60 Common parameters:P-036 is changed to 1 (reverse direction) 0 (positive direction) motor direction conversion parameter. The default is 1 reverse directionP-029 (electronic gear ratio numerator) is 1 by default, the higher the value, the faster the speed(The above parameters are general setting parameters. If you need to modify other parameters, please refer to the manual or contact the technical/sales personnel)The following parameters are rigid adjustment parameters. No adjustment is needed if the equipment is OKP-005 (Speed ring rigidity)P-009 (Position ring rigidity)P-006 (generally, the maximum setting is about 100)P-019 (generally, the maximum setting is about 300)The specific adjustment of rigid parameters depends on the transmission structure and load of the equipment. Contact the after-sales service personnel for specific questions. The T3D series panel consists of 5 LED digital tube displays and 4 buttons ↑、↓、←、SET which are used to display carious states of the systam and set parameters.The operstions are all layered operations,which are expanded layer by layer from the main menu.The operation panel is shown as below: Symbol Name Function POW Power light(none) The decimal point of the second digital tube from the leftlights up to indicate that the servo is under voltage RUN Running light(none) The decimal point of the first digital tube from the leftlights up to indicate that the servo is enabled. ↑ Add key Increase the serial number or value;long press has repeat effect. ↓ Decrease key Decrease the serial number or value;long press has repeat effect. ← Exit key Menu exit, operation canceled. SET Enter Menu entry, parameter modification confirmation or operation confirmation Main menu The first layer is the main menu,there are 4 opreation modes,use the↑、↓keys to change the mode; press theSETkey to enter the second layer and perform specific operations;press the←key to return to the main menu from the second layer.