MTSPF6.6K 200A V6 Based Controller 12S 50V SUPERFOC ESC

Specification: Model No. MTSPF6.6K Input Voltage 3-12S Lipo (12.6V-50V) Hardware VESC6.0 Firmware Updatable Cont Current 200A Burst Current 240A Software VESCTOOL Compatible Heat Sink With Application Electric skateboard, elongboard, fighting robots, ebike, escooter, electric vehicles, friction drive ebike, etc.,   Notice:  Never connect one reclever to two or more V6/V75  based SUPERFOC ESCs or VESCs in an array!  Permanent damage may result from Y-PPM wiring.  Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.   Attention Points when you receive the controller Please: All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out.  When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters. Do not use switching power supply, the instant voltage when switching power supply connect to controller is very high, which would easy damage the controller. Do not push the throttle too hard when test without load, gently and slowly speed up. Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller. Please must remember to change to corresponding modes when you adjust parameters, for example, the VESC default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESCTOOL didn't change to FOC mode, then when you push throttle, would easy burn the controller, same as FOC mode. In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage ERPM= motor pole pairs number * KV * Voltage If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire. For V4 based controller:           Do not suggest to use FOC mode, suggest to use BLDC mode.           If need to use FOC mode, then must use voltage under 20V. The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted Application: Electric skateboard, Esk8, Eskate, Elongboard, Mountainboard, Offroad skateboad, All terrain skateboard, Eskate, E-bike, Electric bike, Electirc motorcycle, E-scooter, Electric scooter, motorized skateboard, ROV/RPVEE, Remote operated vehicles, underwater robots, Underwater robotics, Underwater remotely operated vehicles, Subsea robots, Cablecam, Cable camera, Broadcast, IBC2019, Ultra drones, Security monitoring robots, Robots for security and safety monitoring in harsh terrain, Agile robots, Autonomous agile robots, Security robots, Autonomously monitor security, Combat robots, Fighting robots, Electric surfboard, Efoil, etc., V5 Bluetooth Module:  Model No. MTBLEV5 V5 Upgraded version Features With optocoupler isolation, industrial grade anti-interference, and wired long distance communication Upgrade Function It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient.  With 6 LED Lights status power, communication, data tranmission Compatible Controller Hardware V4 / V6 / V75 based SuperESC  Compatible Software VESCTOOL App Frequency 2.4Ghz Distance 15m Input Voltage 3.3-24V PCB Size 46mm x 32mm V2 Bluetooth Module:  Model No. MTBLEV2 V2 Version With 3 LED Lights status power, communication, database Compatible Controller Hardware V4 / V6 / V75 based SuperESC  Compatible Software VESCTOOL App Frequency 2.4Ghz ARM Processor ARM Cortex-M0 32 bit processor256kB flash&16kB RAM PCB Size 41mm x 21mm Net Weight 5g Antenna Length 90mm Recommend Products: Click below pictures to check more information     Brushless Outrunner Motors: