Community C6 6.5-Inch Ceiling Loudspeaker

Community C6 6.5-Inch Ceiling Loudspeaker The Community C6 comes with a more focused dispersion and a greater low frequency extension than the smaller C4. It is professionally designed containing a proprietary Tru-Phase™ waveguide that comes producing a consistently wide conical polar response up to 16 kHz. The C6 comes featuring a genuine coaxial design with the use of separate magnets for the LF and HF drivers for having reduced distortion and high sensitivity, thereby it permits up to 3 dB greater output level while also requires up to half the amplification power of competing products at the same time. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities. Features High intelligibility with exceptional uniform coverage Consistent, wide dispersion up to 16 kHz True coaxial loudspeakers with HF compression drivers Tru-Phase™ high-frequency waveguide Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails simplify installation Uniquely designed tile bridge support rails prevent ceiling tile sagging External loop-through Euroblock connectors Rear cover with integrated cable clamp (strain relief) and optional conduit knockout Face-mounted adjustable tap position selector switch Selectable 8 ohm or 70V/100V operation Specifications Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 ohm or 70V/100V operation Operating Range: 70 Hz - 13.5 kHz (-10 dB) Frequency Response: 115 Hz - 12.5 kHz (-3 dB) Max Input Ratings (8 ohm): 60W continuous, 150W program 21.9 volts RMS, 43.8 volts momentary peak Transformer Taps: 70V: 30W, 15W, 7.5W, 3.75W, and 8 ohm selectable 100V: 30W, 15W, 7.5W, and 8 ohm selectable Sensitivity (1W/1m): 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands) 91 dB SPL (250 Hz to 4 kHz speech range) Maximum Output 8 Ohm: 109 dB SPL / 115 dB SPL (peak) 70V: 106 dB SPL / 112 dB SPL (peak) 100V: 106 dB SPL / 112 dB SPL (peak) Nominal Impedance: 8 ohms Minimum Impedance: 7 ohms @ 10 kHz Nominal Coverage: 120º conical (1 kHz to 6 kHz ±65°) 120° conical (500 Hz to 6 kHz ±65°) Axial Q / DI: 4.9/6.9, 500 Hz to 6 kHz Crossover Frequency: 2 kHz Recommended Signal Processing: 100 Hz, at 24 dB per octave high pass filter Drivers: LF 1 x 6.5" cone HF 1 x 3/4" exit compression driver Driver Protection: Self-resetting solid state circuitbreaker Input Connection: 4-pole Euroblock connector with two pair of non-interrupt parallel connections Controls: Front-face wattage / low impedance selector switch Enclosure: Corrosion-resistant zinc plated steel Finish: White or black Mounting/Rigging Provisions: 2 ABS mounting clamps with 1.75-inch grip range Grille: Powder coated steel with safety line, white or black finish, paintable Safety Features: 2 x safety hang points Safety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA70 and NFPA 90. Required Accessories: Electronic high pass filter Supplied Accessories: Tile support bridge rails,grille, paint mask, cut-out template, flat screwdriver Optional Accessories: C6-CATR Can Adapter / Trim Ring (white) C6-CATR-B Can Adapter / Trim Ring (black) C6-NCB New Construction Bracket Depth: 9.80" (248.9 mm) bezel diameter 6.49" (164.8 mm) can depth Weight: 7.1 lbs (3.2 kg) Baffle: Reflex loaded UL 94V-0 rated ABS Cutout Diameter: 8.86" (225 mm)