SpeedyBee F7 V3 Stack (50A / 30x30 / BLHeli_32 / 3-6S)
The SpeedyBee F405 V4 BLS 60A 30x30 FC & ESC Stack is an impressive combo for FPV Drones. The flight controller (FC) features an STM32F405 processor, onboard 4-level battery life indicator, 4GB Blackbox SD card slot, DJI Air Unit plug, and ICM42688P gyro. The 60A 4-in-1 ESC boasts genuine 60A output, aluminum alloy heat sink, TVS protective diode, and SMD filtering capacitors. SPECIFICATIONS: Flight Controller: Input Voltage: 3-6S LiPo Power Output:1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A.2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A.3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load. WiFi Support: Used for data transfer, e.g firmware flashing, and Blackbox analysis. I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc. Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV ESC signal M1 - M4 on the bottom side and M5-M8 on the front side. LED: Used for WS2812 LED controlled by Betaflight firmware. UART: 5 sets (UART1, UART2, UART3, UART4, UART6) DJI Air Unit plug: A full DJI Air Unit JST slot onboard BLE Support: Used for Flight Controller configuration Buzzer: BZ+ and BZ- pad used for 5V Buzzer Mounting: 30.5x30.5mm, 4mm hole size Dimensions: 41(L) x 38(W) x 8.1(H)mm OSD: BetaFlight OSD w/ AT7456E chip BlackBox: 500MB onboard data flash BetaFlight Camera Control Pad: Yes ESC Telemetry: UART UART4 RX Target: SPEEDYBEEF7V3 SmartPort: Supported Baro: BMP280 (I2C) MCU: STM32F722 Boot button: Yes RSSI input: Yes IMU: BMI270 USB: Type-C Weight: 9G ESC: Input Voltage: 3-6S LiPo Current Sensor: Supported (Scale=490 Offset=0) Mounting: 30.5x0.5mm, 4mm hole size Dimension: 45.6(L)x40(W)x8.8mm(H) Firmware: SpeedyBee BL32 50A Weight: 19.2g with heat sink Continuous Current: 50Ax4 Burst Current: 55A(5S) Power output: VBAT HELPFUL LINKS: Manual Wire Diagram INCLUDES: (1) SpeedyBee F7 V3 Flight Controller(1) SpeedyBee 50A BLHeli_32 128K ESC(1) 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm - Yellow and Blue(1) 6-Pin SH1.0 GPS module Cable without connector - 100mm(1) 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 30mm(1) 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 60mm(1) 4-Pin SH1.0 to 4-Pin JST1.25 FPV Camera Cable - 60mm(1) 6-Pin SH1.0 GPS module Cable with connector(1) 4-Pin SH1.0 Radio Receiver Cable - 100mm(1) SH 1.0mm 8-Pin Cable -30mm(5) M3 8mm Silicone Grommets(1) DJI 6-Pin Cable - 80mm(1) 35V 1500uF Low ESR Capacitor(1) SH 1.0mm 8-Pin Cable -30mm(5) M3 8.1mm Silicone Grommets(5) M3 Silicone O-Ring(1) XT60 Power Cable NOTES: Manufacturer upgrades, alterations, and processor/firmware changes are frequently made without prior notice. Exact specifications, photos, and links cannot be guaranteed.