MicoAir F405 V2 Flight Controller with BMI088 SPL06, Support Ardupilot INAV, for DJI O3 Air Unit FPV

Description The MicoAir405 v2 is a new cost-effective flight controller runs Ardupilot&INAV firmware, This is the first one which combine the STM32F405 with the high performance IMU sensor BMI088, allowing the flight controllers to have top performance and an attractive price at the same time.The BMI088 is a high-performance 6-axis IMU sensor that comes from Bosch®, its excellent temperature stability and vibration robustness far exceed similar products on the market, making it particularly suitable for drones and robotics applications.The MicoAir405 v2 also integrates a high-performance barometer: spl06, and OSD chip: AT7456E, 2 DC-DC channels to provide 5V-3A and 9V-2.5A power output. These characteristics make this controller particularly suitable for long range FPV drones. Firmware INAV MicoAir405v2 is officially supported by INAV from version 8.0.0. You can also download the old version firmware build by us. GithubArdupilot MicoAir405v2 flight controller board is officially supported by Ardupilot starting from version 4.5.0, you can update the firmware through Mission Planner or download all the firmware files(Copter/Heli/Plane/Rover/etc) here: ArduPilot Firmware Download Also you can use the online firmware builder provided by Ardupilot to customize your firmware for MicoAir405v2: ArduPilot Custom Firmware Builder Specifications MCU: STM32F405RGT6, 168MHz, 1MB Flash IMU: BMI088 Baro: SPL06 OSD: AT7456E MicroSD Card Slot 6x UART 10x PWM 1x I2C 1x SWD 2x ADC (VBAT, Current) USB Type-C BEC 5V 3A output (for controller, receiver, GPS, optical flow or other devices) BEC 9V 3A output (for video transmitter, camera) UART Mapping SERIAL0 -> USB SERIAL1 -> UART1 (DMA-enabled) SERIAL2 -> UART2 (DJI-VTX, DMA-enabled) SERIAL3 -> UART3 (GPS) SERIAL4 -> UART4 (DMA-enabled) SERIAL5 -> UART5 (ESC Telemetry) SERIAL6 -> UART6 (RX6 is inverted from SBUS pin, no DMA on TX6) RC Input The default RC input is configured on the UART6_RX inverted from the SBUS pin. Other RC protocols should be applied at other UART port such as UART1 or UART4, and set the protocol to receive RC data: SERIALn_PROTOCOL=23 and change SERIAL6 _Protocol to something other than ’23’   OSD Support The MicoAir405v2 supports OSD using OSD_TYPE 1 (MAX7456 driver).   VTX Support The SH1.0-6P connector supports a DJI O3 Air Unit connection. Pin 1 of the connector is 9v so be careful not to connect this to a peripheral requiring 5v.   PWM Output The MicoAir405v2 supports up to 10 PWM outputs. Channels 1-8 support DShot. Channels 1-4 support bi-directional DShot. PWM output share grouped and every group must use the same output protocol: 1,2,5,6 are group 1 3, 4 are group 2 7,8 are group 3 9,10 are in group 4   Battery Monitoring The board has a internal voltage sensor and connections on the ESC connector for an external current sensor input. The voltage sensor can handle up to 6S LiPo batteries. The default battery parameters(for Ardupilot) are: BATT_VOLT_PIN 10 BATT_CURR_PIN 11 BATT_VOLT_MULT 21.2 BATT_CURR_SCALE 116.5 Compass The MicoAir405v2 does not have a built-in compass, but you can attach an external compass using I2C on the SDA and SCL connector.   Physical Mounting: 30.5 x 30.5mm, Φ4mm Dimensions: 36 x 36 x 8 mm Weight: 9g   Technical SupportIf you encounter any usage issues or require technical support after receiving your product, please feel free to contact us. You can reach us via email at info@robofusion.net.Our technical support team will respond to your inquiry within 48 hours. We promise to provide you with professional solutions to ensure you make the most out of our products.We also welcome any feedback or suggestions you may have regarding our products. Your input is invaluable to us and will help us continually improve and enhance our products and services.