F7 Stack V3 3-6S 30x30 Stack with F7 FC and 32Bit 128K 50A ESC
The SpeedyBee F7 V3 Stack includes an F722 flight controller and a 50A 128K ESC. Featuring bluetooth configuration, barometer, OSD, Blackbox, a built-in FC LiPo monitoring system, and many more features, this stack is the perfect addition to your FPV build. Features 1500uF Low ESR Capacitor with TVS Protective Diode 500MB Onboard Blackbox Flash memory 8 Motor output perfect for X8 Cinelifters 30.5 x 30.5mm Mounting Pattern FC LiPo Monitoring System SpeedyBee 50A 128K ESC CNC Heatsink Shield Built-in Barometer 128KHz PWM 4 LED Plugs F722 FC Buzzer Specifications SPEEDYBEE F7 V3 FLIGHT CONTROLLER Power Output: 1) 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on the front side, and 6 +5V output included in the connectors on the bottom side. The total current load is 2A. 2) 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 4A. 3) Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load Supported. Designed for 3.3V-input receivers. Up to 500mA current load. WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis. I2C: Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc. Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV ESC signal M1 - M4 on the bottom side and M5-M8 on the front side. LED: Used for WS2812 LED controlled by Betaflight firmware. UART: 5 sets (UART1, UART2, UART3, UART4, UART6) DJI Air Unit plug: A full DJI Air Unit JST slot onboard BLE Support, used for Flight Controller configuration Buzzer: BZ+ and BZ- pad used for 5V Buzzer Mounting: 30.5x30.5mm, 4mm hole size Dimensions: 41(L) x 38(W) x 8.1(H)mm OSD: BetaFlight OSD w/ AT7456E chip BlackBox: 500MB onboard data flash BetaFlight Camera Control Pad: Yes ESC Telemetry: UART UART4 RX Power input: 3S - 6S Lipo Target: SPEEDYBEEF7V3 SmartPort: Supported Baro: BMP280 (I2C) MCU: STM32F722 Boot button: Yes RSSI input: Yes IMU: BMI270 USB: Type-C Weight: 9G SPEEDYBEE 50A BLHELI_32 128K ESC Current Sensor: Supported (Scale=490 Offset=0) Mounting: 30.5x0.5mm, 4mm hole size Dimension: 45.6(L)x40(W)x8.8mm(H) Firmware: SpeedyBee BL32 50A Weight: 19.2g with heat sink Continuous Current: 50Ax4 Power input: 3S - 6S LiPo Burst Current: 55A(5S) Power output: VBAT Includes 1x Speedy Bee F7 V3 Flight Controller 1 4-Pin SH1.0 to SH1.0 Analog VTX Cable 60mm - Yellow and Blue 1x 6-Pin SH1.0 GPS module Cable without connector - 100mm 1x 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 30mm 1x 4-Pin SH1.0 to 3+ 2-Pin JST1.25 FPV Camera Cable - 60mm 1x 4-Pin SH1.0 to 4-Pin JST1.25 FPV Camera Cable - 60mm 1x 6-Pin SH1.0 GPS module Cable with connector 1x 4-Pin SH1.0 Radio Receiver Cable - 100mm 1x SH 1.0mm 8-Pin Cable -30mm 5x M3 8mm Silicone Grommets 1x DJI 6-Pin Cable - 80mm 1x SpeedyBee 50A BLHeli_32 128K ESC 1x 35V 1500uF Low ESR Capacitor 1x SH 1.0mm 8-Pin Cable -30mm 5x M3 8.1mm Silicone Grommets 5x M3 Silicone O-Ring 1x XT60 Power Cable Wiring Diagram