DMX512 Dim CV LED drivers 150w (IP67)

The 12V 150W dmx driver rgb led supports RDM control & setting. Using hand-held device to set NFC address & adjust output voltage. Smarts DMX 512 drivers covers the wattage from 30w to 300w. Model SMT-12150-XC-A SMT-24150-XC-A X=1 , 2,  3,  4,  5 for DIM (DW);  CCT(TW);  RGB;  RGBW;  RGBW+CCT (RGBCW)   DC Voltage 12V 24V Voltage Tolerance ±0.5V Voltage Regulation ±0.5% Rated current CH1+CH2+CH3+CH4+CH5=12.5A CH1+CH2+CH3+CH4+CH5=6.25A Rated power 150W Load Regulation ±2% Input Voltage Range 100-277VAC Frequency Range 47-63Hz PowerFactor(Typ.)@ full load PF≥0.97@230VAC THD(Typ.)@ full load ≤10% Efficiency(Typ.)@ full load 91%@230VAC 92.5%@230VAC AC Current(Max.) 1.85A 1.85A Inrush Current(Typ.) 88A (Twidth 120us measured at 50% I peak, COLD START, 230VAC) Leakage current <0.50mA Protection Short Circuit Hiccup mode ,recovers automatically after fault condition is removed Over Loading ≤120%  Hiccup mode ,recovers automatically after fault condition is removed Over temperature 100℃±10℃ shut down o/p voltage, automatically recover after cooling. Environment Working TEMP. -40~+60℃ (see below derating curve) Working Humidity 20~95%RH, non-condensing Storage TEMP. Humidity -40~+80℃,10~95%RH TEMP .coefficient ±0.03%/℃(0~50℃) Vibration 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes Safety&EMC Safety standards EN61347-1   EN61347-2-13 (EU)   &  UL8750  UL1310 (US) Withstand voltage I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC (EU) & I/P-O/P:1.5KVAC(US) Isolation resistance I/P-O/P:100MΩ/500VDC/25℃/70%RH EMC EMISSION EN55015  EN61000-3-2 ,3-3 (EU) & FCC Part 15 B (US)  (≥60% loading) EMC Immunity EN61000-4-2,3,4,5,6,11, EN61547 Others Net Weight 0.75KG Dimension 277x78x25mm (LxWxH) packing 10PCS/CTN   Notes 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. 2. Tolerance: includes set up tolerance, line regulation and load regulation . 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. [Custom Product Tab] ※Input Rubber cable 3*1.0mm²(VDE approval), the Y/G cable connect with (FG) , Brown with AC (L), Blue with AC(N) (EU) Input SJOW Rubber cable 3*18AWG (UL approval), the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US)※Dimming cable: Purple (D+), Brown (D-) and Gray (GND) connect to DMX dimmer / system.※Output cable to be connected to LED Light; DIM (DW) dimming: Rubber cable Black is output ( V+) Positive, White is output (V-) negative CCT (TW) dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative RGB dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG Black is output ( V+) Positive, Red (R-), Green (G-) and Blue (B-) are output (V-) negativeRGBW dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (W-) are output (V-) negativeRGB+CCT dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (CW-) and Yellow (WW-) are output (V-) negative.;※Please make sure you connect these correctly ,otherwise your product will not work correctly and could be damaged.Note: there is external antenna at output side. Don't disassemble! ■ DMX512 address setting Operation ※The default address for the DMX driver is 001.※Address settings device: ※Address settings:① RDM setting address:Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual. ② NFC setting address:The DMX address can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver. ■ Adjust output voltage Operation ※Adjust output voltage slightly for DMX512 driver1) The driver output voltage can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver. 2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 5. Such as SMT-24030-XC-P, default is level 5 corresponding to 24V. By adjusting output voltage slightly, you could get 23.2v to 25V freely. ■ See figure below Simple operation about DMX512 address reset and adjusting output voltage slighting by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) [/Custom Product Tab]