JL Audio XDM Marine Amplifier 6-Channel Full-Range 600 Watt 24v

JL Audio XDM600/6-24V 6 Ch. Class D, Full-Range Car/Marine Amplifier, 600 W, for 24V SystemsModel: XDM600/6-24VFor 24V systems only: 6-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 6 @ 2 Ohm / 75 W x 6 @ 4 Ohm - 28.8VThe incredibly flexible XDM600/6-24V packs a serious full-range wallop and delivers a stunning 100 watts to each of its six channels into 2 ohms (28.8V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency.Suitable for car or boat installations, the XDM600/6-24V is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades.With the XDM600/6-24V, you have plenty of great use options. Configure it as a six-channel satellite amplifier with 75 W x 6 @ 4 ?, or bridge four of its channels to create a staggered power four-channel amplifier with 200 W x 2 @ 4 ? for your front satellites and 75 W x 2 @ 4 ? for your rear satellites. You can also drive two subwoofers with 200 W each, plus a pair of satellites with 75W x 2.The XDM600/6-24V includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all six amplifier channels directly from the driver's seat or cockpit.Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24 volt may result in damage to the product and will void the warranty.Specifications Rated Continuous (RMS) Power @ 28.8 V @ 4 Ohms 75 W RMS x 6 @ 2 Ohms 100 W RMS x 6 Bridged @ 4 Ohms 200 W RMS x 3 Rated Continuous (RMS) Power @ 25 V @ 4 Ohm 60 W RMS x 6 @ 2 Ohms 90 W RMS x 6 bridged @ 4 Ohms 180 W RMS x 3 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ohm >150 / 50 Hz Damping Factor @ 2 Ohms >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ohms per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or 4 or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A What's in the Box: XDM600/6-24V Wrench Badge Manual