OBDStar X300 DP Plus Full Immobilizer Device - C Package

Product DescriptionOBDSTAR X300 DP Plus C Package Full Configuration covers all functions of OBDSTAR X300 DP Key Master and supports more functions such as ECUprogramming, Throttle programming, Airbag reset, Injector code+Suspension matching+Gear learning+CVT learning+DPF+ECU cloning+Adapter(P001programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester) NOTE: Please check the supported car list of vehicle functions before you buy this device. If you are not sure whether the function or vehicle is supported, please feel free to inquiry us online  X300 DP Plus supports English only It doesn't support the following car models: DAIHATSU/ PROTON/ MAHINDRA/ MARUTI/ TATA/ HOLDEN/ LADA/ PERODUA/ IRAN. Please register first after receiving the product. X300 DP PLUS Registration and Upgrade GuideDifferences Among OBDSTAR X300 DP Plus C Package (Full Version), A Package, and B Package: Functions Regional market Software Configuration X300 DP plus Remark 　 　 A package B package C package 　 Immobilizer / Remote programming European cars VW/Audi/Skoda/Seat (Standard) √ √ √ 　 VW/Audi/Skoda/Seat (Advanced) √ √ √ add NEC 24C64 2014-key programming. BMW (Standard) 　 　 　 　 BMW (Advanced) √ √ √ Add FEM/BDC key programming, ISN code reading, etc. Volvo √ √ √ 　 The other European cars √ √ √ 　 Asian cars Hyundai /Kia (Standard) 　 　 　 　 Hyundai /Kia (Advanced) √ √ √ Add 47/8A/46 smart key pin code reading Toyota /Lexus (Standard) 　 　 　 　 Toyota /Lexus (Advanced) √ √ √ For Middle east cars, it adds H chip all keys lost (Immo box reset) The Asian cars √ √ √ 　 North American cars Ford(Standard) 　 　 　 　 Ford (Advanced) √ √ √ Add Ford after 2015 key programming functions, I.E: Mobdeo,Edge,Taurus,Escort,EVEREST,Explorer,F-150 SVT Raptor,Mustang,Lincoln MKZ, MKC and Continental 2015 - etc. GM(Standard) 　 　 　 　 GM(Advanced) √ √ √ 　 The other American & Chinese cars √ √ √ Can perform BMC pin code reading on these cars: -2017 Lacrosse, Lacrosse, Trax, Envision, GL8, MALIBU, AVEO, Excelle before 2015, Cruze, etc. Cluster Calibration 　 All cars cluster calibration 　 √ √ 　 　 　 4-system diagnosis 　 　 　 Engine, Transmission, ABS, airbag reset OBDII Diagnosis 　 Full functions diagnosis 　 　 √ Full-system all-cars diagnosis Special function 　 Oil service reset 　 　 √ Reset the Oil Service Light on 　 Manual remote setting 　 　 　 Some cars only support manual remote settings. 　 ABS bleeding 　 　 √ After replacing the ABS pump and related components. 　 Battery matching 　 　 √ After the battery is changed, you need to match the battery. 　 ECU programming 　 　 √ 　 　 The car with EPB replace brake pads 　 　 √ An electronic Parking Brake release 　 Throttle programming 　 　 √ Used to clear the learning value after cleaning the throttle, otherwise, it will cause high idle speed. 　 Airbag reset 　 　 √ Used to clear airbag ECU collision data after a vehicle collision, otherwise, the ECU cannot be reused 　 TPMS reset 　 　 √ Used for a reset after tire pressure alarm 　 Steering angle reset 　 　 √ Replacement of data lost after steering angle change or power off 　 OBDII Engine 　 　 √ Used to diagnose the car with OBD protocol. 　 DPF Regeneration 　 　 √ Diesel Particulate Filter Operational 　 Injector coding 　 　 √ Used to match and code the injector after replacement 　 Suspension match 　 　 √ Used to match and set the suspension after adjusting. 　 Gear learning 　 　 √ Used to learn the crankshaft position sensor after power off (only the domestic vehicle equipped with the Delphi system has this function) 　 CVT learning 　 　 √ Used to reset the learning value after the maintenance of CVT transmission 　 EEPROM 　 　 √ Read and write the EEPROM; read 8-pin IC chip password and reset some models anti-theft 　 Key Renew 　 　 √ Renew the used keys to solve the problem that used keys cannot be matched to other models 　 Steering angle repair 　 　 √ Used for the repair of lost data of vehicle steering angle sensor 　 ECU Clone 　 　 √ Used for copying the program when replacing the new/second-hand computer. 　 Switch activation 　 　 √ 　 Hardware 　 P001 Programmer unit √ √ √ 　 　 C001 circuit board √ √ √ 　 　 C002 circuit board √ √ √ 　 　 W001 data cable √ √ √ 　 　 W002 data cable √ √ √ 　 　 W003 data cable √ √ √ 　 　 Toyota smart key emulators √ √ √ 　 　 Remote Tester √ √ √ 　 　 Anti-theft Induction coil √ √ √ Used to test if the coil can send out the transmit signal. X300 DP Plus C Full Configuration Diagnostic Function: Diagnose the electronic control system of prevailing vehicle models covering Asian, European, American, and Chinese. Diagnosis functions include: Read DTCS, Clear DTCS, Read data stream, Special functions etc. Classify special functions: ABS, EEPROM Adapter, Battery match, CVT learning, EPB, Gear learning, Immobilizer, TPMS (low tire) reset, Cluster calibrate, ECU programming, steering angle reset. Specially designed for Android platform with clear and user-friendly interface. X300 DP Plus C Full Configuration Software Advantages:1: ECU CloneECU Clone means ECU duplication.The device copies all the data from the original vehicle ECU and then writes all data copied into ECU with the same hardware to realize the same ECU function with the original vehicle.2.Clone directly when replacing a new or a used ECU!Without online matching in the 4S store or removal of ECU bonding wire for reading and writing! Directly write without dismantling OBD!     3.Three features for ECU Clone:  A. Free of 4S online: break monopoly from 4S, benefiting automobile maintenance industryB. Simplified operation procedures: realize foolproof operationC. Non-dismantling with zero risks: read and write data without dismantling ECU Switch activation function: (Today many instruments or audio of vehicles activate secondary power supply to go into power-on status by relevant module CAN communication on the vehicle,but sometimes an instrument or an audio is separated from the vehicle CAN BUS network, causing startup failure when it needs to be repaired by an auto technician.This function can simulate CAN communication to activate the secondary power supply, so the instrument or the audio enters into power-on status. In this way,it not only can test and verify the instrument or the audio but also save an enormous cost for an auto technician to purchase a large number of startup platformsof various vehicles and wiring harnesses!) Add “Help” functions:1. Contain built-in testable vehicle models, upgrade announcements, features, help notes and wiring diagrams, etc.2. Car list: directly get it on the device3. Upgrade Announcement: all details are available on the device4. Customers can look up the features or uniquely support functions on the device5. Help notes: built-in help notes for each model or function8. Wiring diagrams: built-in ECU wiring diagrams, more intuitionistic and convenient OBDSTAR X300 DP Plus C Full Configuration Hardware Advantages: 1. Built-in VCI box, communication more stable2. 8-inch touchscreen, more intuitionistic3. Can be charged directly via OBD interface4. Practical and high-end gift box5. Industrial design with silicone case6. Back bracket design: Can prop on the steering wheel or stand on the table, easier to operate7. With simulated key 1 applies to the vehicle with 94/D4 type of smart key.8. 3 in 1 P001 programmer: combined with EEPROM adapter + RFID adapter+ Key Renew adapter9. Add the clip of reading SOP 8PIN EEPROM10. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)11.Maintenance Database12.Remote Assistant13.One Key Upgrade How to use OBDSTAR X300 DP Plus Induction Coil? 1. Functional Overview: Induction Coil is used to detecting the key induction coil failure of the vehicle. OBDSTAR X300 DP Plus A+B+C Full Configuration Technical Parameters Operation system  Android 5.1.1 CPU Exynos4418 Dual Core ARM Cortex A9 1.4GHz Battery 3700mA, rechargeable polymer lithium battery Extension memory card  32G Micro SD (TF) card supported Memory capacity  1GB Storage capacity  32GB LCD  8.0 inch LCD resolution  1280*800 Touch screen  Capacitive touch screen Camera  5 mega rearview camera Wi-Fi  supported Working temperature -10℃ ~ 55℃（14℉ ~ 131℉ ） Storage temperature -20℃ ~ 70℃（-4℉ ~ 158℉ ） Dimension  254mm*174*mm*35mm Other Configuration: A Package: Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester) OBDSTAR X300 DP Plus vs. OBDSTAR X300 DP  Picture Obdstar X300  DP Plus Obdstar X300  DP Hardware & Design Better Good Screen size and industrial design √ × Back holder √ × Work separately without VCI √ × Charged by OBDII √ × 4 Toyota emulators √ × P001 programmer √ × Wiring harness for new functions, such as ECU cloning and switch activation √ Software/Update Immobilizer  √ √ Mileage √ √ EEPROM √ √ ECU Clone √ × Switch activation function √ × "Help" function - covers built-in support car list,upgrade announcement,help  notes and wiring diagrams √ × No need to pay for a software update for FREE during the valid time (one year) √ × Register directly on a tablet Please connect to the network after receiving the device, enter the settings to register first.