3470 Series Commercial Fan Forced Surface Mounted Ceiling Heater with Single Pole Thermostat, Radial Louver Cone Diffuser, USRCD-001-070

United States/Heaters: Downflow Forced Fans/3470 Series Commercial Fan Forced Surface Mounted Ceiling Heater with Single Pole Thermostat Spec Sheet (.pdf) General Characteristics of 2600 Series Linear Louvered Diffuser Down Flow Unit Heater The 2600 Series Linear Louvered Diffuser is a down flow unit heater; constructed with 16 gauge steel cabinet with epoxy powder coated finish and control compartment with a hinged and latched access door. OSHA guards standard with all models. For industrial and commercial use. For indoor use where heat needs to be forced down from ceiling. The heating element is corrosion resistant with steel sheath and steel spiral fins. Overheat protection: All units come equipped with manual reset limit controls to de-energize the heater should an over-temperature situation occur. The motor is totally enclosed, 1 speed, 1 phase permanently lubricated, thermally protected motors with unit bearings on 3KW to 20KW models. Totally enclosed, 2 speed, 1 phase permanently lubricated, thermally protected motors with sleeve bearings on 24KW to 50KW models. Axial flow fan blade - 1570 RPM max. All Models equipped with Fan Purge which allows Fan to operate after elements are de-energized to purge residual heat. Temperature controls: 208V, 240V, 277V, and 480V units have built in 24 volt transformer for low voltage remote thermostat application. 600V units have in-built 240V control on 5-20 Kw models; 25-50Kw models have 24V control. 25Kw models may operate as 2 stage heaters if 2 stage remote thermostats are used. Disconnect switch: all models equipped with in-built disconnect except F3F2640, F3F2650 and H3H2650. Installation: unit can be mounted using optional mounting bracket or field constructed angle iron bracket Not recommended for mounting with threaded rod or chain The 2600 Series Linear Louvered Diffuser shown with standard wire guard. Diffusers are field installed Minimum mounting height is 6 feet. This product is ETL-CETL listed. Made in the U.S.A. Product Applications of 2600 Series Linear Louvered Diffuser Down Flow Unit Heater Industrial and Commercial use where heat needs to be forced down from ceiling. Used to heat factories, shops, bakeries, gymnasiums, warehouses, offices, etc. For indoor use. Warranties and Guaranties of 2600 Series Linear Louvered Diffuser Down Flow Unit Heater Manufacturer's Limited Warranty: 1 year. Keywords and Search Terms Radial Louver Cone Diffuser, Con Diffuser Radial Louver, Radial Louver Heater, Heater Radial Louver, Heater Radial Louver Industrial, Heater Radial Louver Commercial, Heater Radial Louver for Indoor, Heater Radial Louver for Office, Heater Radial Louver for Homes, Heater Radial Louver for Hotels, Heater Radial Louver for Motels, Heater Radial Louver for Resort, Heater Radial Louver for Malls, Heater Radial Louver for Stores, Heater Radial Louver for Shops, Heater Radial Louver for Cafes, Heater Radial Louver Restaurant, Heater Radial Louver Hospitals, Heater Radial Louver for Gyms, Heater Radial Louver for Banks, Heater Radial Louver for Mills, Heater Radial Louver Theaters, Heater Radial Louver for Bars, Heater Radial Louver for Clubs, Heater Radial Louver Golf Clubs, Heater Radial Louver for Museum, Heater Radial Louver for Garage, Heater Radial Louver for Halls, Heater Radial Louver Bakeries, Heater Radial Louver Car Washes