Fluke 805 FC Vibration Meter
Model: Fluke 805 FC Vibration Meter Part Number: 805 FC Ordering Number: 1C6305 Datasheet The reliable, repeatable, accurate way to check bearings and overall vibration Make go or no-go maintenance decisions with confidence. The Fluke 805 FC Vibration Meter is the most reliable vibration screening device available for frontline mechanical troubleshooting teams that need repeatable, severity-scaled readings of overall vibration and bearing condition. Includes: USB cable Storage case Belt holster Quick reference guide CD-ROM (includes MS Excel template and documentation) Two (2) AA batteries Battery type AA (2) Lithium Iron Disulfide Battery life 250 measurements Size (L x W x H) 24.1 cm x 7.1 cm x 5.8 cm(9.5 in x 2.8 in x 2.3 in) Weight 0.40 kg (0.89 lb) Connectors USB mini-B 7-pin, external sensor jack (SMB connector) Features What makes the Fluke 805 FC the most reliable vibration screening device available? Innovative sensor design minimizes measurement variations caused by device angle or contact pressure Consistent data quality at both low and high frequency ranges Four-level severity scale assesses urgency of problems for overall vibration and bearing condition Exportable data via USB Trending in Microsoft® Excel using pre-built templates Overall vibration measurement (10 Hz to 1,000 Hz) for acceleration, velocity and displacement units of measurement for a wide variety of machines Crest Factor+ technology provides reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz Compare vibration levels with ISO-10816 severity scales and store results to the Fluke Connect Cloud Get authorization to take next steps in an instant if machine health is at risk via Fluke Connect™ Share-Live™ video call* Colored lighting system (green, red) and on-screen comments indicate how much pressure needs to be applied to take measurements Temperature measurement with Spot IR Sensor increases diagnostic capabilities On-board memory holds and saves up to 3,500 measurements External accelerometer support for hard to reach locations Flashlight for viewing measurement locations in dark areas Large screen with high resolution for easy navigation and viewing Specifications Low frequency range (overall measurement) 10 Hz to 1,000 Hz High frequency range (CF+ measurement) 4,000 Hz to 20,000 Hz Severity levels Good, satisfactory, unsatisfactory, unacceptable Vibration limit 50 g peak (100 g peak-peak) A/D converter 16-bit Signal to noise ratio 80 dB Sampling rate Low frequency: 20,000 HzHigh frequency: 80,000 Hz Real time clock backup Coin battery Sensor Sensitivity 100 mV g ± 10% Measurement range 0.01 g to 50 g Low frequency range (overall measurement) 10 Hz to 1,000 Hz High frequency range 4,000 Hz to 20,000 Hz Resolution 0.01 g Accuracy At 100 Hz ± 5% of measured value External Sensor Note: Fluke supports but does not provide external sensors Frequency range 10 Hz to 1,000 Hz Bias voltage (to supply power) 20 V dc to 22 V dc Bias current (to supply power) Maximum 5 mA Amplitude Units Acceleration g, m/sec² Velocity in/sec, mm/sec Displacement mils, mm Infrared Thermometer (Temperature Measurement) Range -20 °C to 200 °C (-4 °F to 392 °F) Accuracy ±2 °C (4 °F) Focal length Fixed, at ~3.8 cm (1.5") Firmware External interfaces USB 2.0 (full speed) communication Data capacity Database on internal flash memory Upgrade Through USB Memory Up to 3,500 measurements Radiated Emission Electrostatic discharge: burst Standard EN 61000-4-2 Electromagnetic interference Standard EN 61000-4-3 RE Standard CISPR 11, Class A Environmental Operating temperature -20 °C to 50 °C (-4 °F to 122 °F) Storage temperature -30 °C to 80 °C (-22 °F to 176 °F) Operating humidity 10% to 95% RH (non-condensing) Operating/storage altitude Sea level to 3,048 meters (10,000 feet) IP rating IP54 Vibration limit 500g peak Drop test 1 meter