DIY 560mm Carbon Fiber DIY Drone Folded Frame Kit W/ 700KV Brushless Motor 40A ESC 1455 Props APM2.8 With compass RC Quadcopter
DIY Drone 560mm Carbon Fiber Foldable Frame With 700KV Brushless Motor 40A ESC 1455 Propellers APM2.8 With compass RC Helicopter Frame kit is unassembly,any quesions , pls contact us freely . Set B package included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 Set C package included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 11.1V 4400MAH XT60 Battery x1 B3 pro Charger x1 Set D package included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 Radiolink AT9S Radio with RD9S Receiver x1 Set E pacakge included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 Radiolink AT9S Radio with RD9S Receiver x1 11.1V 4400MAH XT60 Battery x1 B3 pro Charger x1 Set F pacakge included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 Radiolink AT9S Radio with RD9S Receiver x1 Gimbal x1 Set G pacakge included : Carbon fiber folding frame kit x1 HYD3508 700kv brushless motor x4 1455 carbon fiber propeller x2 XT60 cable x1 black reverse buckle tie x1 Non-folding Landing gear x1 Antenna Holder x1 GPS X1 APM2.8 With compass X1 MWC connection cable X5 15cm Servo extention cable x1 Radiolink AT9S Radio with RD9S Receiver x1 Gimbal x1 More Details : Frame kit: Wheelbase: 560mm Fit for Motor:2212-3508(920kv - 700kv) Fit for ESC: 20A-40A Height of the Landing Skid: 190mm Fit for Propeller: 10-12 inch Propeller: High quality 100% 3K all carbon fiber board which imported from Japan improve material. Each pair of propellers has perfect dynamic poise and static balancing which balance by manpower. Especially improves the air-powered efficiency and aerofoil stability. High quality ultra-light carbon fiber propellers especially designed for multicopters. Carbon fiber forward propeller*1 Carbon fiber reverse propeller*1 Length:14inch,Pitch 5.5,Main Hole Dia 4mm,Side Holes Dia 3mm,Center distance 12mm Motor: Motor KV: 700KV Shaft: 4.0mm No-load Currency (A): 0.4A Maximum Currency (A): 18.0A Power: 198W Weight: about 90g Input Voltage: 2-4S LOPO Suitable Propeller: 12"-15" Props ESC: Types: long, short Current: 40A Output capacity: continuous current 40A, short-time current 55A (not less than 10 seconds) Power input: 2-4 lithium batteries(Not Included) BEC output: 5V@3A (linear regulator mode - linear mode) Maximum speed: 210,000 rpm for 2-pole motor, 7000 rpm for 6-pole motor, 35,000 rpm for 12-pole motor Size: (Approx) 68x25x8mm APM2.8 - Arduino Compatible! - Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally - Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer - Onboard 4 MegaByte Dataflash chip for automatic datalogging - Optional off-board GPS, uBlox LEA-6H module with Compass. - One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000. - Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties. - Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively. Charger : Input Voltage : 100 - 240V AC50 / 60Hz Output Current: 3*800mA Suitable for 2 cell and 3 cell Li-Po Batteries Led Indicator: When power is on : Orange Stand by mode : Green Battery Charging : Red Battery Full : Green AT9S Transmitter : Channels: 10ch/12ch Mode: Mode 1 or Mode 2 Signal: SBUS/PWM/PPM/CRSF Frequency: 2.4GHz ISM bands (2400MHz to 2483.5MHz) Channel Bandswidth: 5.0 MHz Spread Spectrum: DSSS&FHSS/CRSF Modulation Mode：QPSK Adjacent Channel rejection: >38dbm Transmission Power: DSSS & FHSS <100mW(20dbm) CRSF: 10mW/25mW/100mW/500mW/1W/2W(Optional) Operating Current: DSSS&FHSS < 90mA@12V CRSF Depends on the transmission power selecte Operating Voltage: 7.4~18.0V 4096 Section Precision Screen: 2.8 inches 16 colorful screen, 240*320 pixels Channel: 10 channels , 5-10 channels are customized Size: AT9S- 183*100*193mm Weight: 0.88kg Control Range: DSSS&FHSS - 4KM in the air (Maximum range is tested in an unobstructed area free of interference) Compatible receivers: 12CH - R12DSM, R12DS, 10CH- R9DS, R6DS,R6DSM CRSF: RX from BLACKSHEEP R12DSM Receiver Specifications Signal: SBUS/PPM Channel: 12CH Control Distance: 4000m on air Working Voltage: 4.8-6V Working Current: 40-180mA（input voltage: 5V） Size: 30*15mm Weight: 2.5g Gimbal: - Simple structure and light weight,CNC aluminum alloy structure - Brushless motor direct drive - With anti-vibration rubber balls,easy to adjust - Compatible with Gopro3+, 3,2,1 - with 2pcs 2208 motors and V3 gimbal controller,sensor - with motor protector which can help heat dissipation - gimbal weight: 400g Note: 1.This gimbal is not include gopro 3. 2.Users need learn how to install the component and test its effects. It's will get better results after a period of testing. 3.Assembled tuning good, no assembly instructions