4.3"IPS TFT LCD Display Module 800x480 High Brightness Capacitive - RGB
4.3 Inch Tft Lcd Module 800x480 RGB Screen with/without Capacitive Please feel free to contact us if you need program code, data sheet of the screen or Chip ic,etc. Product Description： 4.3-inch color screen, support 24BIT RGB 16.7M color display, display rich colors Support 800x480, the display effect is very clear Support 24 bit RGB parallel bus transmission Compatible with RGB interface connection of punctual atomic development board and wildfire development board It supports the switching between capacitive touch screen and resistance touch screen, and the capacitive touch screen can support up to 5 touch points Provides a rich sample program for STM32 platforms Military-grade process standards, long-term stable work Provide underlying driver technical support Product Parameters： Display Color：RGB888 16.7M (compatible with rgb5665k) color Screen Size ：4.3(inch) Model No:ZO MRG4301(no touch), ZOMRG4311(have touch) Type：TFT Driver IC：None Resolution：800*480 (Pixel) Module Interface：24Bit RGB parallel interface Touch Screen Type：Capacitive or Resistive touch screen Touch IC：FT5426(Capacitive touch), XPT2046(Resistive touch) Active Area ：95.04x53.86(mm) Module PCB Size：105.41x86.41(mm) Operating Temperature：-10℃~60℃ Storage Temperature：-20℃~70℃ Input Voltage：5V IO Voltage：3.3V Power Consumption：50mA(The backlight is off), 165mA(The backlight is the brightest) Rough Weight(Net weight)：95(g) Interface Definition：①--Capacitive touch screen circuit②--Resistance touch screen circuit③--Disp resistance④--P2 interface (compatible with atomic RGB interface)⑤--P3 interface (compatible with wildfire RGB interface)⑥--Module ID defines resistance (only for atomic program) 1. Switch touch screen If you choose to connect the capacitive touch screen, please weld the capacitor touch screen circuit; Select the connection resistance touch screen, please weld the resistance touch screen circuit; If you often need to switch the touch screen, after welding other circuits, only switch the drain resistance in the dotted line box; 2. Precautions for disp resistance welding When connecting the wildfire development board for use, the disp resistance must be removed, otherwise the screen will not display after the development board is reset; When connected to wildfire i When using the MX6ULL ARM Linux development board, you need to remove the DISP resistor and the three resistors in parallel, otherwise the development board will not run. When connecting atomic development board, f407 minimum system board or esp32 development board, disp resistance must be welded, otherwise the screen will not be displayed. 3. P2 and P3 interface pins are described as follows: P2 interface (compatible with atomic RGB interface) pin description Number Pin name Description 1 VCC5 Power input pin（connect to 5V） 2 VCC5 Power input pin（connect to 5V） 3~10 R0~R7 8-bit RED data pin 11 GND power ground pin 12~19 G0 ~ G7 8-bit GREEN data pin 20 GND power ground pin 21~28 B0 ~ B7 8-bit GREEN data pin 29 GND power ground pin 30 PCLK Pixel clock control pin 31 VSYNC Vertical synchronous signal control pin 32 HSYNC Horizontal synchronous signal control pin 33 DE Data enable signal control pin 34 BL LCD backlight control pin 35 TP_CS Capacitor touch screen reset pin (resistance touch screen chip selection pin) 36 TP_MOSI Data pin of IIC bus of capacitance touch screen (write data pin of SPI bus of resistance touch screen) 37 TP_MISO Resistance touch screen SPI bus read data pin (capacitance touch screen not used) 38 TP_CLK IIC bus clock control pin of capacitive touch screen (SPI bus clock control pin of resistance touch screen) 39 TP_PEN Touch screen interrupt control pin (low level when touch is generated) 40 RST LCD reset control pin (effective at low level) P3 interface (compatible with wildfire RGB interface) pin description Number Pin name Description 1 VCC5 Power input pin（connect to 5V） 2 VCC5 Power input pin（connect to 5V） 3 VCC3.3 Power input pin（connect to 3.3V） 4 VCC3.3 Power input pin（connect to 3.3V） 5 GND power ground pin 6~13 R0 ~ R7 8-bit RED data pin 14~21 G0 ~ G7 8-bit GREEN data pin 22~29 B0 ~ B7 8-bit BLUE data pin 30 PCLK Pixel clock control pin 31 HSYNC Horizontal synchronous signal control pin 32 VSYNC Vertical synchronous signal control pin 33 DE Data enable signal control pin 34 DISP LCD display enable pin (enable at high level) 35 BL LCD backlight control pin 36 GND power ground pin 37 TP_RST Capacitor touch screen reset pin(enable at low level) 38 TP_PEN Touch screen interrupt control pin (low level when touch is generated) 39 TP_SDA Data pin of IIC bus of capacitance touch screen 40 TP_SCL IIC bus clock control pin of capacitive touch screen How to connect the development board