7.0 inch IPS TFT LCD Display 800x480 with RGB

7 inch Capacitive Touch Lcd 800x480 Tft color RGB Display Module 24-bit Please feel free to contact us if you need program code, data sheet of the screen or Chip ic,etc. Product Description： 7.0-inch color screen, support 24BIT RGB 16.7M color display, display rich colors Support 800x480 resolution screen switching, the display effect is very clear Support 24 bit RGB parallel bus transmission Compatible with RGB interface connection of punctual atomic development board and wildfire development board Use capacitive touch screen to support 5 touch points Provides a rich sample program for STM32 platforms Military-grade process standards, long-term stable work Provide underlying driver technical support   Product Parameters： Display Color：RGB888 16.7M (compatible with rgb5665k) color Model No:ZOMRG7101(no touch), ZOMRG7111(have touch) Screen Size ：7.0(inch) Type：TFT Driver IC：None Resolution：800*480 (Pixel) Module Interface：24Bit RGB parallel interface Touch Screen Type：Capacitive touch screen Touch IC：FT5426 Active Area ：800x480: 153.84x85.63(mm) Module PCB Size：164.90x124.27(mm) Operating Temperature：-10℃~60℃ Storage Temperature：-20℃~70℃ Input Voltage：5V IO Voltage： 3.3V Power Consumption : 67mA(The backlight is off), 467mA(The backlight is the brightest) Rough Weight(Net weight)：236(g)   Interface Definition： ①--DITHB selection circuit②--U/D selection circuit③--L/R selection circuit④--Screen resolution selection circuit⑤--P2 interface (compatible with atomic RGB interface)⑥--P3 interface (compatible with wildfire RGB interface)⑦--B7 Data line pull resistance (required to define module ID, applicable to atomic program) 1. Screen internal Dithering display function settings Weld the 0 position resistance of DITHB and disconnect the 1 position resistance to enable the internal Dithering display function of the display panel; Weld the 1 position resistance of DITHB, disconnect the 0 position resistance, and turn off the internal Dithering display function of the screen; Default welding 0 position resistance, disconnect 1 position resistance 2. Screen display up and down flip settings Weld the resistance at position 0 of U / D, disconnect the resistance at position 1, and the screen will turn down; Weld the resistance at position 1 of U / D, disconnect the resistance at position 0, and the screen will turn upward; Default welding 0 position resistance, disconnect 1 position resistance 3. Screen display left and right flip settings weld the resistance at position 0 of L / R, disconnect the resistance at position 1, and the screen will turn to the left; Weld the resistance at position 1 of L / R, disconnect the resistance at position 0, and the screen will turn right; Default welding 1 position resistance, disconnect 0 position resistance 4. Screen resolution selection As shown in the screen resolution selection circuit, the module supports screen switching of 800x480 and 1024x600 resolutions. Weld M0 resistance to GND, M1 resistance to VCC, select 1024x600 resolution; Weld M0 resistance to VCC, M1 resistance to GND, and select 800x480 resolution; 5. Precautions for connecting to wildfire development board If connected to wildfire i When using the MX6ULL ARM Linux development board, it is necessary to remove the pull resistance on the B7 data line referred to by label 7 and the M0 and M1 resistance referred to by label 4, otherwise the development board will not run 6. P2 and P3 interface pins are described as follows: P2 interface (compatible with atomic RGB interface) pin description Number Pin name Description 1 VCC5 Power input pin（connect to 5V） 2 VCC5 Power input pin（connect to 5V） 3~10 R0~R7 8-bit RED data pin 11 GND power ground pin 12~19 G0 ~ G7 8-bit GREEN data pin 20 GND power ground pin 21~28 B0 ~ B7 8-bit GREEN data pin 29 GND power ground pin 30 PCLK Pixel clock control pin 31 HSYNC Horizontal synchronous signal control pin 32 VSYNC Vertical synchronous signal control pin 33 DE Data enable signal control pin 34 BL LCD backlight control pin 35 TP_CS Capacitor touch screen reset pin (resistance touch screen chip selection pin) 36 TP_MOSI Data pin of IIC bus of capacitance touch screen (write data pin of SPI bus of resistance touch screen) 37 TP_MISO Resistance touch screen SPI bus read data pin (capacitance touch screen not used) 38 TP_CLK IIC bus clock control pin of capacitive touch screen (SPI bus clock control pin of resistance touch screen) 39 TP_PEN Touch screen interrupt control pin (low level when touch is generated) 40 RST LCD reset control pin (effective at low level)   P3 interface (compatible with wildfire RGB interface) pin description Number Pin name Description 1 VCC5 Power input pin（connect to 5V） 2 VCC5 Power input pin（connect to 5V） 3 VCC3.3 Power input pin（connect to 3.3V） 4 VCC3.3 Power input pin（connect to 3.3V） 5 GND power ground pin 6~13 R0 ~ R7 8-bit RED data pin 14~21 G0 ~ G7 8-bit GREEN data pin 22~29 B0 ~ B7 8-bit BLUE data pin 30 PCLK Pixel clock control pin 31 HSYNC Horizontal synchronous signal control pin 32 VSYNC Vertical synchronous signal control pin 33 DE Data enable signal control pin 34 DISP LCD display enable pin (enable at high level, the module is not used) 35 BL LCD backlight control pin 36 GND power ground pin 37 TP_RST Capacitor touch screen reset pin(enable at low level) 38 TP_PEN Touch screen interrupt control pin (low level when touch is generated) 39 TP_SDA Data pin of IIC bus of capacitance touch screen 40 TP_SCL IIC bus clock control pin of capacitive touch screen     How to connect the development board