(PRE-ORDER) Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz
Pre-Orders shipping ASAP! The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor: ROBO 1002 23500KV Electronics: GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX Props: 1609 - 4 blade 40mm 1.5mm Shaft Camera: Flywoo 1S Nano Camera V3 Receiver: ExpressLRS 2.4GHz Weight: 26g Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed: 80km/h (approximate) GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port：1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 Onboard 5.8g VTX Output power: 25mw~250mw switchable Frequency: 40CH Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Flywoo 1S Nano Camera V3 Model: Flywoo 1S Nano Camera V3 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 2.1g Includes 1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards