Happymodel Mobula6 ECO 2024 1S 65mm HDZero ELRS 2.4GHz Ultra Light Micro FPV Whoop - BNF
Happymodel Mobula 6 ECO 2024 is the first BNF that uses HDZero ECO Bundle. HDZero ECO Bundle is designed to bring digital FPV to more pilots by offering a low cost, light weight, and durable alternative to analog video. The digital video signal has stable color reproduction and 720p progressive scan video with the low latency HDZero is known for. This budget-friendly Air Unit is a groundbreaking product—it’s the first VTX/camera combination that utilizes a HD composite video signal, eliminating the need for a delicate MIPI cable. The ECO FPV System was meticulously designed for ultra-lightweight drones like Tiny Whoops, where every fraction of a gram counts. The camera’s huge 98deg vertical FOV is perfect for fast indoor proximity flying. The ECO VTX weighs approximately 4.5g, while the camera (including wires) comes in at about 1.6g. With the included 0.2g dipole antenna, the entire Eco Bundle weighs about mere 6.3g in total. Check out our collection of Micro BNF/RTF/PNP Whoops and the rest of our Happymodel Products! Features: AIO Flight controller with Serial ELRS Receiver Compatible with HDZERO system Equipment with the lightest brushless motors-SE0702 only 1.49gram HDZERO NEW ECO VTX and Camera ready Smooth and powerful Compatible for 1S Lipo/LIHV Onboard blackbox read Specifications: Brand Name: HAPPYMODEL & HDZERO CO-Brand Model: Mobula6 ECO 2024 Frame wheelbase: 65mm Weight: 23.16 gram without battery Size: 81mm*81mm*45mm Compatible with 1S Lipo battery or Lihv battery Battery Plug: GNB A30 Motor： Mode: SE0702 KV28000 Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.49g No.of Cells(Lipo):1S only Propellers： Materials: PC Inch: 31mm Pitch: 0.8 in Weight: 0.21g Mount hole diameter: 1mm Flight controller： SuperX HD ELRS Betaflight 4.4.2 firmware ready Firmware target: CRAZYBEEF4DX MCU:STM32F411CEU6 (100MHz, 512K FLASH) Sensor: BMI270 or ICM42688P (SPI connection) Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update Bluejay ESC Firmware ready Built-in 5V 1A BEC Built-in voltage detection No betaflight analog osd chip Onboard 4in1 ESC： Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support ESC-Configurator and BLHELI_S Suite configurator Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz Default protocol: DSHOT300 Battery Connector: GNB A30 (Compatible with BT2.0) Onboard Serial ExpressLRS receiver： RF Frequency: 2.4GHz Antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Receiver protocol: CRSF Default firmware version: ExpressLRS V3.0.1 The same hardware with Happymodel EP1 receiver Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through HDZERO ECO VTX: Composite HD Video interface 1S-3S Input 25mW/200mW RF output 25.5×25.2 M2 soft mounting Antenna Retention 32.4×32.5mm (29x29mm inner) 4.5grames/4mm Thickness (w/o shielding) HDZERO ECO Camera: Image Sensor : 1/3” Resolution: 720@60fps 4:3 LENS: FOV D:150° H:120° V:98° Shutter: Rolling Shutter Net Weight: 1.6g (With Cable) Dimensions: L14mm*W14mm*H13mm Package Includes: 1x Mobula6 2024 1S 65mm whoop Drone Frame +Canopy 1x SuperX HD ELRS AIO flight controller 1x HDZero ECO VTX 1x HDZero ECO Camera 4x SE0702 KV28000 brushless motor 1x Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw) 1x Spare Canopy 1x Screw Driver 1x Propeller disassemble tool