Happymodel Mobula6 ELRS 2.4GHz 1s 65mm Brushless FPV Brushless Whoop Drone (NO BATTERY INCLUDED) - Choose Version
ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable. Now we are about to release Mobula6 equipped with ExpressLRS RC link system, the new Mobula6 elrs would coming out with a new 0802 brushless motor, that would be the lightest brushless motors all over the world. We’re sure this would be a good option for you in the Tiny Whoop Season. Update Log: Updated to ICM42688P gyro. Mobula6 ELRS 2.4Ghz version comes with Updated ELRSF4 2G4 V3.1 flight controller since 25th Feb V3.1 Version flight controller Updated MPU6000 changed to ICM20689 because of MPU6000 discontinued Onboard VTX changed to OPENVTX support 0mw~400mw Pre-install Betaflight firmware which support ELRS V2.0 TX firmware Now with Caddx Ant, no longer with Runcam 3. Check out our Mobula 6 and Parts collection and our entire Happymodel Products! Description: Brand: Happymodel Item Name: Mobula6 ELRS 2.4GHz 1S 65mm Brushless whoop drone BNF version Wheelbase: 65mm Size: 80mm*80mm*37mm Weight: 18.7g Voltage:1S Specifications: Motor KV: Race = KV25000, Standard = 19000KV Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.46g No.of Cells(Lipo):1S only Propellers: HQprop31mmx2 Center Thickness:5mm Prop Disk Diameter:31mm Center Hole Inner diameter:1.0mm Weight:0.2g Flight controller: ELRS F4 2G4 flight controller V3.1 built-in SPI expresslrs 2.4G receiver MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: ICM42688P Board size: 28.5 * 28.5MM Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in ExpressLRS 2.4G receiver Built-in 5V 1A BEC Built-in voltage detection Onboard 4in1 ESC: MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT600 Onboard SPI ExpressLRS 2.4GHz Receiver: Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHzAntenna : SMD antenna Telemetry output Power: <12dBmReceiver protocol: SPI ExpressLRS Could bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module ExpressLRS version 1.0.0 or 1.0.1 both compatible Onboard 5.8g VTX: Output power: 25mw~200mw Frequency: 37CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 37 channels With Race band Smartaudio ready Lipo Battery: Capacity:300mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 57mmx12mmx7mm Weight: 8gConnector: PH2.0 Package Includes: 1 x Happymodel Mobula6 ELRS 2.4GHz 1s 65mm Brushless FPV Brushless Whoop Drone - Chosen Version 1 x HQPROP 31mm bi-blade propellers(4cw+4ccw) 1 x 1S Lipo/LIHV USB Charger 1 x Propeller disassemble tool