Tannoy CMS503DCBM 5" Full Range Ceiling Loudspeaker with Dual Concentric Driver (Blind Mount) [Priced Individually, Sold in Pairs]

Description Tannoy CMS503DCBM 5" Full Range Ceiling Loudspeaker with Dual Concentric Driver (Blind Mount) [Priced Individually, Sold in Pairs] Tannoy CMS503DCBM is a professionally designed 5" Full-Range Ceiling Loudspeakers made by Tannoy comes including two full-bandwidth, high-power handling, and high-sensitivity loudspeakers built around Tannoy's CMS 3.0 Ceiling Monitor System technology. It is based on a Dual Concentric point-source driver, the speaker is capable of delivering a wide and consistent broadband directivity, intelligibility, and an accurate and linear response. The Dual Concentric driver design comes featuring an Omnimagnet technology and the Torus Ogive Waveguide device, together providing consistent and controlled directivity along with improved high frequency response. Time alignment and coherence between low and high frequencies is capable of enhancing the performance both on- and off-axis. The baffle is made for providing a subtle extension to the wave-guide effect designed for additional sonic benefits. The loudspeaker also comes featuring a extra clamp extension for accommodating thicker ceiling panels, and a locking design that is capable of preventing an inadvertent over-screwing. Magnetic grille attachment is enabling the easy removal and fitting designed for custom painting. It is possible to utilize a 16-Ohm driver which makes it ideal for use in high-performance, low-impedance systems. A low insertion-loss 30W transformer is included, with convenient front switching for taps at 30W, 15W, and 7.5W, that comes with an additional 3.75W tap for traditional constant voltage systems. Each speaker is supplied along with an integral back can, ready to install as a single unit. The removable locking connector comes with a screw terminals intended for secure wire termination and loop-thru facility. Strain relief is provided by a clamping mechanism designed for use along with a plenum-rated cable or conduit, while the spring-loaded and self-aligning clamps are making ar quick and easy installation at the same time. Each loudspeaker is supplied with a grille, two tile support rails, and a C-ring. Dual Concentric driver design utilizing Omnimagnet technology Torus Ogive Waveguide device for broadband directivity High power and high sensitivity with extended frequency response and very low distortion Improved LF performance for applications where genuine bottom end is a must Convenient front tapping switch for settings Magnetically adhering grille system for easy custom painting Three-clamp, self-aligning mounting system UV resistant baffle and grille Suitable for: Voice alarm systems, multi-zone foreground music & paging systems, offices, business music systems, airports, convention centers, hotels, waiting rooms, houses of worship, retail outlets, shopping malls, lounges, bars, cruise ships, and courtrooms Specifications Driver 5" / 130 mm Dual Concentric Omnimagnet driver Low Frequency Driver 1.38" / 35 mm voice coil, treated multi-fiber paper pulp cone High Frequency Driver 0.79" / 20 mm PEI dome Frequency Response 85 Hz to 50 kHz at -3 dB Frequency Range 74 Hz to 54 kHz at -10 dB System Sensitivity 89 dB (1 W = 4 V for 16 Ohms) Nominal Coverage Angle 90° Power Handling Average: 60 WProgram: 120 WPeak: 240 W Recommended Amplifier Power 120 W @ 16 Ohms Nominal Impedance 16 Ohms Maximum SPL Average: 107 dBPeak: 113 dB Transformer Taps 70 V: 30 W (165 Ohms) / 15 W (330 Ohms) / 7.5 W (660 Ohms) / 3.75 W (1320 Ohms) / OFF & low impedance operation100 V: 30 W (330 Ohms) / 15 W (660 Ohms) / 7.5 W (1320 Ohms) / OFF & low impedance operation Enclosure Back Can: Zinc plated steelBaffle: Reflex loaded UL 94V-0 rated ABSGrille: Steel, with weather resistant coating Safety Features Safety ring located at rear of enclosure for load bearing safety bond Clamping Characteristics Security toggle clampClamping Range: 0.4-2.4" / 1-6 cmRecommended Clamp Torque: 1.5 Nm Mount Blind mount complete with fixed back can Cable Entry Cable clamp & squeeze connector for conduit up to 0.9" / 22 mm Connectors Removable locking screw terminals with "loop thru" Compliance UL-1480, UL-2043, CE Dimensions Bezel Diameter: 8.1" / 20.1 cmFront of Ceiling to Rear of Back Can: 7.4" / 18.8 cmHole Cutout Diameter: 7.5" / 19.0 cm Weight 9.04 lb / 4.1 kg